Abstract：Copper foams with nine different cell structural parameters were prepared by ultrasonic assisted electrodeposition process. The viscosity coefficient [K1], inertia coefficient [K2] and nusselt number [Nu] of copper foams were tested using water as working fluid in laminar -turbulent transition region (0.4～1.3 m/s). The influence of pore density and porosity of copper foams on flow, convective heat transfer and overall performance was discussed. Results show that [K1] and [K2] decrease by about 80% and 50%, and the [Nu] increases by about 100% when pore density increases from 10 ppi to 45 ppi at the same porosity, while [K1] and [K2] decrease by about 30% and 20%, and[Nu]increases by about 50% when porosity decreases from 96% to 90% at the same pore density. From the view point of overall performance, copper foam with pore density of 10 ppi, 96% porosity is a clear optimum.
刘汉强，赵 鹏，浦玉萍，沈 伟，朱黎冉. 孔密度和孔隙率对泡沫铜换热性能的影响[J]. , 2015, 25(02): 46-51.
LIU Han-qiang, ZHAO Peng, PU Yu-ping, SHEN Wei, ZHU Li-ran. Influence of pore density and porosity on heat transfer performance of copper foam. , 2015, 25(02): 46-51.
[1]卢天健, 何德坪, 陈常青, 等.超轻多孔金属材料的多功能特性及应用[J].力学进展, 2006, 36(4):517-535[2]Zhao C Y.Review on thermal transport in high porosity cellular metal foams with open cells[J].International Journal of Heat and Mass Transfer, 2012, 55(13,14):3618-3632[3]Ozmat B, Leyda B, Benson B.Thermal applications of open-cell metal foams[J].Materials and manufacturing processes, 2004, 19(5):839-862[4]Boomsma K, Poulikakos D, Zwick F.Metal foams ascompact high performance heat exchangers[J].Mechanics of Materials, 2003, 35(12):1161-1176[5]Mancin S, Zilio C, Diani A, et al.Experimental air heat transfer and pressure drop through copper foams[J].Experimental Thermal and Fluid Science, 2012, 36(1):224-232[6]Kim S Y, Kang B H, Kim J H.Forced convection from aluminum foam materials in an asymmetrically heated channel[J].International Journal of Heat and Mass Transfer, 2001, 44(7):1451-1454[7]纪献兵, 徐进良.流体在超轻多孔金属泡沫中的流动和换热特性[J].化工学报, 2009, 60(1):21-27[8]Lu T J, Stone H A, Ashby M F.Heat transfer in open-cell metal foams[J].Acta mater., 1998, 46(10):3619-3635[9]De J P, T’Joen C, Huisseune H, et al.Influence of geometrical parameters of open-cell aluminum foam on thermohydraulic performance[J].Heat Transfer Engineering, 2013, 34(14):1202-1215[10]Muley A, Kiser C, Sundén B, et al.Foam heat exchangers: a technology assessment[J].Heat Transfer Engineering, 2011, 33(1):42-51[11] 赵鹏, 浦玉萍, 黄春晖, 等.超声波对聚氨酯泡沫塑料化学镀铜的影响[J].材料工程, 2008, (4):43-46[12]赵鹏, 浦玉萍.超声波对电沉积泡沫铜结构及性能的影响[J].中国表面工程, 2008, 21(1):45-49[13] 刘伟, 范爱武, 黄晓明, 多孔介质传热传质理论与应用[M].北京: 科学出版社, 2006.15-33.[14] 乔瑞华, 赵鹏, 朱黎冉, 等.电沉积泡沫铜孔径与渗透性能的关系研究[J].材料工程, 2010, (6):30-35[15]Calmidi V V, Mahajan R L.Forced convection in high porosity metal foams[J].Journal of Heat Transfer, 2000, 122(3):557-565[16]Jazi H R S, Mostaghimi J, Chandra S, et al.Spray-formed,metal-foam heat exchangers for high temperature Applications[J].Journal of Thermal Science and Engineering Applications, 2009, 1(3):58-64[17]Webb R L.Performance evaluation criteria for use of enhanced heat transfer surfaces in heat exchanger design[J].International Journal of Heat and Mass Transfer, 1981, 24(4):715-726[18]王英双, 张晓屿, 刘志春, 等.花格板换热器的流动与传热[J].化工学报, 2012, 63(S1):99-106
2015, Vol. 25 
